Technology & safety

Why LFP, and what keeps it safe.

Chemistry sets the ceiling on safety. Design decides whether you reach it. LFP gives a higher thermal-runaway threshold than nickel-rich chemistries; the rest is thermal management, fusing, detection and venting.

ChemistryLFP (LiFePO4)
Cycle life6,000 to 80% SoH
CoolingLiquid, ΔT ≤ 3 K

Chemistry

LFP is the conservative choice. That is the point.

Lithium iron phosphate has lower energy density than nickel-rich chemistries and no cobalt or nickel in the cathode. For a stationary asset that must run for fifteen years, energy density is not the binding constraint.

Property LFP NMC Na-ion
Cell energy density140–180 Wh/kg200–260 Wh/kg100–160 Wh/kg
Cycle life (typical)4,000–8,0002,000–4,0003,000–5,000
Thermal stabilityHighModerateHigh
Cobalt / nickelNoneYesNone
Low-temperature behaviourModerateModerateGood
Supply chain maturityMatureMatureEmerging

Industry-typical ranges for stationary cells, for orientation only. Procurement is against the cell supplier's certified datasheet.

The trade we make. An LFP block is larger and heavier than an NMC block of the same energy. In exchange, the chemistry is harder to drive into thermal runaway and contains no cobalt or nickel exposure in the bill of materials.

Cathode

LiFePO4 — iron and phosphate, no cobalt or nickel.

Design life

15 years to 80% state of health at specified duty.

Calendar ageing

Low float-voltage stress; suited to daily cycling.

Recyclability

Established hydrometallurgical recovery for lithium and iron phosphate.

Architecture

Three levels of battery management.

Each level can isolate what is below it. A cell fault trips a module; a module fault isolates a rack; a rack fault disconnects the block without taking the plant down.

  1. BMS 1 Cell & moduleVoltage, temperature and balancing per cell group; fusing at module level 8S1P
  2. BMS 2 RackSOC/SOH estimation, insulation monitoring, breaker control, coolant temperature 416S
  3. BMS 3 BlockAggregates 12 racks, enforces current limits, reports to PCS and EMS 5.016 MWh
  4. EMS PlantDispatch, SoC management, alarm handling, historian and reporting Plant-wide

State estimation

Coulomb counting corrected against open-circuit voltage at rest, per rack rather than per block.

Isolation

A failed rack is disconnected at its own breaker; the remaining eleven stay in service.

Diagnostics

Cell-level trends retained for the life of the asset — the data that settles a warranty claim.

Thermal

Temperature is the variable you can actually control.

Cycle life and safety both degrade with cell temperature and, more sharply, with temperature difference across a rack. We cool at the module base with a glycol loop, and hold ΔT inside 3 K in steady state.

Above 45 °C ambient the block derates on a published curve rather than continuing at full power. Below −20 °C, charging is inhibited until the pack is warmed — the BMS enforces it, not the operator.

Coolant loop: a chiller feeds a supply manifold, twelve racks run in parallel between the manifolds, and the return manifold closes the loop. CHILLER glycol loop rack rack rack rack SUPPLY MANIFOLD RETURN MANIFOLD 12 racks in parallel · cell ΔT ≤ 3 K
Fig. 05 — Coolant loop, indicative

Fire safety

Five layers, not one.

No single device makes a battery safe. Protection is a stack of independent measures, each of which assumes the one before it has failed.

Layer Measure What it assumes has already failed
1 · CellLFP chemistry and incoming cell gradingNothing — this is the first line
2 · ModuleCell-level fusing and thermal interface to the cold plateAn internal cell defect
3 · DetectionAspirating smoke, volatile organic compounds and cell temperatureFailure of the electrical protections
4 · SuppressionClean agent at rack and plenum levelDetection has fired but the event is not contained
5 · StructuralDeflagration venting, separation distances, emergency planSuppression has not stopped propagation

Suppression agent and venting design are finalised per project against the applicable code set (NFPA 855, local fire authority, or both) and the site layout.

Controls

The plant is a control problem as much as a battery.

The PCS and EMS decide whether the asset earns its capital. We specify them against your connection study and dispatch strategy rather than bundling whatever ships with the enclosure.

Grid code

LVRT/HVRT, reactive range, ramp rate and frequency response configured to the interconnection requirement.

Grid forming

Available on selected PCS platforms — specified where the grid study requires it, not by default.

Protocols

Modbus TCP as standard; IEC 61850 and DNP3 for utility SCADA integration.

Cyber

Network segmentation, no inbound vendor access by default; designed against IEC 62443 practice.

Compliance

Standards framework, stated plainly.

Certification status is confirmed per product and per market, in writing, before contract. We publish the framework we design to — not a wall of badges.

Standard Scope Applies to
IEC 62619Safety of secondary lithium cells and batteries for industrial useModule, rack
IEC 63056Safety requirements for secondary batteries in electrical energy storageModule, rack, block
IEC 62477-1Safety of power electronic converter systemsPCS interface
UL 1973Batteries for use in stationary, vehicle and light electric rail applicationsModule, rack, block
UL 9540ACell-to-cell and cell-to-block thermal runaway fire propagation testingBlock
NFPA 855Installation standard for stationary energy storage systemsPlant layout, fire strategy
UN 38.3Transport of lithium batteriesModule, rack, block
BISIndian standards registration for cells and batteriesProduct registration

What due diligence gets you. On request: the type-test reports for the exact configuration, the declaration of conformity, the fire-test evidence for the block, and the FAT procedure used at our facility — issued as controlled documents with revision numbers. Request the pack.

Roadmap

What comes after LFP.

We add a chemistry when it is cheaper per delivered kilowatt-hour over the asset life — not when it is announced.

Now

LFP

The platform in production: 314 Ah prismatic cells, module to block, liquid-cooled.

2027

Long-duration variants

2 h, 4 h and 8 h block configurations for tenders that specify duration rather than power.

2028

Sodium-ion qualification

Cycle-life and low-temperature qualification for cost-sensitive C&I and long-duration duty.

Watch

Solid state

Tracked, not committed. Commercial stationary cells are not yet bankable at our scale.

Technical due diligence

Send your engineer.

We would rather answer the hard questions before contract than after. Test reports, failure-mode analysis and factory access are available to your technical adviser.